Sample it · four routes
Sampling
Sample the keyboard’s FM synth into Logic or Koala, sample on the device itself with open firmware, and finger-drum the results from the pads.
Last updated
On this page
Four routes. A and B use the SMK-37 as a sound source and your Mac or iPad as the sampler — the most flexible and the easiest. C samples on the keyboard itself, which needs different firmware. D is how you play any of them.
Out of the box the keyboard is an FM synth only (manual). For samples on the device you need SMK37 OPEN or community firmware (route C).
A. Mac: resample the FM synth into Quick Sampler
You need firmware V016, a USB-C data cable straight into the Mac, and headphones on the keyboard.
- Make it visible as audio. Audio MIDI Setup → Show Audio Devices should list the SMK-37 with an input. Note its sample rate (Format).
- Logic Pro → Settings → Audio → Devices: Input Device = the SMK-37. Match the project sample rate.
- Make it play: press PATCH, latch it, choose a sound.
- Capture. Either record an audio track (a few pitches — low, middle and high C — plus one long held note with its release), or open Quick Sampler → Recorder mode, set the input to the keyboard, choose Wait for signal to pass Threshold, then record and play (Apple).
- Trim and load. Drag the region into Quick Sampler; tick Optimized to auto-trim and tune it (Apple). Set the root note, and loop it if it’s a pad sound.
- Put it on the pads. One-shots: put Quick Sampler in a Drum Machine Designer cell, then use Learn Note and hit a pad (Apple). Chops: Slice mode spreads slices across consecutive keys.
- Silence the original. Turn PATCH off (or Local Control off) so you don’t hear the live FM voice under your sample.
Silent? Latch PATCH and re-check the input device. Fallback: the 3.5 mm output into any audio interface. Details on Mac + Logic Pro.
B. iPad: into Koala Sampler or Logic Pro for iPad
- Connect USB-C (charge the keyboard first — the iPad powers it), turn PATCH on and latch it.
- Koala → Settings → Input source lists USB audio inputs (Koala manual). Look for the SMK-37. USB audio from the keyboard on iPadOS is unverified — if it isn’t listed, use the 3.5 mm out into a USB-C interface.
- Sample: tap a Koala pad → Sampling → record while you play a key on the SMK-37 → trim. Repeat across pads.
- Play it back: keyboard pads in Note mode (Midi Suite), Koala MIDI Channel = All, then Map MIDI. See iPad Pro.
- Logic Pro for iPad works the same way: pick the keyboard as audio input, record, drop the region into Quick Sampler.
No audio path at all? Load the same DX7 bank into KQ Dixie or Dexed on the iPad and sample that.
C. Sample on the device
SMK37 OPEN (official) — the safe route
One of the eight tracks can be a Sampler. Sample slots 1–8 sit on the first eight white keys (C D E F G A B C), regardless of octave; the pads keep their drum mapping (README). Samples are loaded from the browser workbench — there’s no on-device recording.
- Open the Elite (or Pro) workbench in desktop Chrome/Edge and connect (workbench).
- Projects & sounds → 8-slot sample bank → Read device sample bank first, so you don’t overwrite what’s there.
- Pick a slot, choose a WAV, name it (up to 15 characters), set start/end, audition.
- Encode & replace browser slot, then Write device sample bank — this replaces the whole bank for every project.
- Back up the bank as a
.fm1sfile. Projects don’t contain sample audio, so back samples up separately.
| Storage | About 19.5 seconds shared across all 8 slots (README) — keep to short one-shots |
|---|---|
| Input | WAV (8–32-bit or float), mono or stereo, 8–192 kHz, up to 120 s before trimming (workbench help) |
| Editing | Level, Tune, Length, Choke (open/closed-hat style), Variation, velocity low-pass |
| Sampler shows EMPTY | Use Check / initialize samples — no reflash needed |
Stretch the 19.5 seconds by using the 808, 303 and PSG engines on other tracks — they need no sample memory.
Community firmware with sampling
All third-party: read Firmware & hacking and back up first.
- Snoop37 — the SMK-37 port of SLOOP, a four-track groovebox (installer). On the FM-1, SLOOP has four user-sample slots (~7.4 s each) and a web CHOP editor that slices any recording onto keys (SLOOP README). Whether the full sample editor works on the SMK-37 port is unverified.
- SLOOP SMK-37 Multichannel — sends six USB audio stems to your DAW, handy for resampling each track (repo).
- ECHOFIELD — a granular sampler (about 10–14 s of sample memory) with a companion web app. Its own repo says it’s untested on hardware: experimental (repo).
D. Finger-drum it
- Note repeat on the keyboard: hold NOTE REPEAT and set Gate, Swing, Tempo and Rate (1/4 to 1/32T) on K1–K4, latch with K5, then hold a pad (manual). Whether the repeats go out over USB MIDI is unverified — watch Logic’s Event List. Note repeat blocks the internal sequencer.
- Pressure: pad aftertouch can modulate filter or volume in your DAW.
- Soft hits: reviewers find the pads hard to play quietly; try another pad velocity curve (GLOBE K5) (Audiowords).
- On SMK37 OPEN: the pads are drum-mapped to the Sampler and 808 tracks. Press REC while stopped to step-record; during playback, REC records in time.
Choose your path
| You want… | Do this | Watch out |
|---|---|---|
| Just a controller | Stock V016; map knobs with Learn; USB for recording, Bluetooth for jamming | Pad notes and CCs aren’t published — read them from your DAW |
| A standalone synth | Presets + PARA/FX; load DX7 banks | Few parameters editable on the keyboard |
| A groovebox | SMK37 OPEN first (factory restore built in), then Snoop37 | New Bluetooth names (…Open_BLE); samples only via the workbench |
| To hack on it | The open SDK or the FM-1 → SMK-37 porting kit; back up the flash with M-Flasher | Brick risk; model-specific packages; Windows toolchain |
Sources & links on this page (13)
- manual manualf.oss-cn-hongkong.aliyuncs.com
- Apple support.apple.com
- Apple support.apple.com
- Apple support.apple.com
- Koala manual manual.koalasampler.com
- README github.com
- workbench open.m-vave.com
- installer genkigenki.github.io
- SLOOP README github.com
- repo github.com
- repo github.com
- Audiowords audiowords.net
- FM-1 → SMK-37 porting kit github.com
Page last updated 2026-11-21 · Back to top